Follow
sasikumar chandrabalan
Title
Cited by
Cited by
Year
Effect of mechanical activation on the kinetics of sulfuric acid leaching of beach sand ilmenite from Orissa, India
C Sasikumar, DS Rao, S Srikanth, B Ravikumar, NK Mukhopadhyay, ...
Hydrometallurgy 75 (1-4), 189-204, 2004
1502004
Dissolution studies of mechanically activated Manavalakurichi ilmenite with HCl and H2SO4
C Sasikumar, DS Rao, S Srikanth, NK Mukhopadhyay, SP Mehrotra
Hydrometallurgy 88 (1-4), 154-169, 2007
982007
Electrodeposition of nanostructured ZnO thin film: a review
M Kumar, C Sasikumar
Am. J. Mater. Sci. Eng 2 (2), 18-23, 2014
482014
Analysis of premature failure of a tie bar in an injection molding machine
C Sasikumar, S Srikanth, SK Das
Engineering Failure Analysis 13 (8), 1246-1259, 2006
352006
Energetics of mechanical activation–Application to ilmenite
C Sasikumar, S Srikanth, NK Mukhopadhyay, SP Mehrotra
Minerals Engineering 22 (6), 572-574, 2009
332009
Formability analysis of aluminium alloy by Erichsen cupping test method
M Singh, AK Choubey, C Sasikumar
Materials Today: Proceedings 4 (2), 805-810, 2017
202017
Development of hierarchical layered nanostructured α-MoO3 thin films using dc magnetron sputtering
SDCS Kumar
Mater. Res. Express 3 (2016) 106405 3 (106405), 2016
192016
Microstructures and mechanical properties of Al-Si-Mg-Ti/egg shell particulate composites
S Shamim, H Singh, C Sasikumar, DK Yadav
Materials Today: Proceedings 4 (2), 2887-2892, 2017
172017
Failure of evaporator tubes initiated by lamellar tearing during the commissioning of a waste heat recovery boiler
S Srikanth, SK Das, C Sasikumar, B Ravikumar
Engineering Failure Analysis 14 (1), 262-278, 2007
172007
Analysis of die angle in deep drawing process using FEM
AK Choubey, G Agnihotri, C Sasikumar, M Singh
Materials Today: Proceedings 4 (2), 2511-2515, 2017
162017
Development of hard and wear resistant surface coating on Ni-Cr-Mo steel by surface mechano-chemical carburization treatment (SMCT)
JN Sahu, C Sasikumar
Journal of Materials Processing Technology 263, 285-295, 2019
152019
Experimental and Mathematical Analysis of Simulation Results for Sheet Metal Parts in Deep Drawing
CS Ajay Kumar Choubey, Geeta Agnihotri
Journal of Mechanical Science and Technology, 2017
122017
Effect of vanadium addition to Al-Si alloy on its mechanical, tribological and microstructure properties
A Kumar, C Sasikumar
Materials Today: Proceedings 4 (2), 307-313, 2017
122017
A novel method for development of hard nano crystalline surface through SMAT and mechanical alloying
JN Sahu, C Sasikumar
Materials Today: Proceedings 3 (6), 1968-1976, 2016
122016
Plasma catalysis: a feasible solution for carbon dioxide valorization?
N Anoop, S Sundaramurthy, JM Jha, S Chandrabalan, N Singh, J Verma, ...
Clean Technologies and Environmental Policy 23 (10), 2789-2811, 2021
102021
Surface nano-crystallizationof AISI 304 stainless steel through shot peening technique
P Tadge, PK Gupta, C Sasikumar
Materials Today: Proceedings 2 (4-5), 3245-3250, 2015
102015
Numerical validation of experimental result in deep-drawing
AK Choubey, G Agnihotri, C Sasikumar
Materials Today: Proceedings 2 (4-5), 1951-1958, 2015
92015
A water droplet erosion-induced fatigue crack propagation and failure in X20Cr13 martensitic stainless-steel turbines working at low pressure
MS Khan, C Sasikumar
Engineering Failure Analysis 139, 106491, 2022
72022
Where does the energy go in high energy milling?
C Sasikumar, S Srikanth, R Kumar, TC Alex, SP Mehrotra
62011
Effect of Natural Weathering and Mechanical Activation on the Acid Dissolution Kinetics of Indian Beach Sand Ilmenites
C Sasikumar, DS Rao, S Srikanth, BRV Narashimhan, B Ravikumar, ...
Metals Materials and Processes 18 (3/4), 211, 2006
62006
The system can't perform the operation now. Try again later.
Articles 1–20