Effect of Asymmetric Geometry on the Flexibility of Stent A Syaifudin, R Takeda, K Sasaki JMES The International Journal of Mechanical Engineering and Sciences 1 (1), 1-7, 2017 | 9 | 2017 |
Studies of the effect of melt spinning on the electrochemical properties of the AB2 Laves phase alloys ID Wijayanti, L Mølmen, RV Denys, MN Guzik, S Gorsse, JL Bobet, ... JMES The International Journal of Mechanical Engineering and Sciences 5 (1), 2021 | 5 | 2021 |
Numerical study of blended winglet geometry variations on unmanned aerial vehicle aerodynamic performance FD Pertiwi, A Wahjudi JMES The International Journal of Mechanical Engineering and Sciences 6 (1 …, 2022 | 4 | 2022 |
Numerical study of bach-bladed savonius wind turbine with varying blade shape factor K Ibrahim, VS Djanali, N Ikhwan JMES The International Journal of Mechanical Engineering and Sciences 4 (2 …, 2020 | 4 | 2020 |
Design and analysis of ECVT on electric powered vehicles for determining the speed ratio HS Maulana, IN Sutantra JMES The International Journal of Mechanical Engineering and Sciences 5 (2 …, 2021 | 3 | 2021 |
Experimental Study on Effect of Injection Pressure to Spray Characteristics, Performance and Emissions of DieselEngine DI 20 C Using Biodiesel Fuel AAK Mahanggi, B Sudarmanta, H Soebagyo JMES The International Journal of Mechanical Engineering and Sciences 2 (1 …, 2018 | 3 | 2018 |
Numerical study effect of fluidizing air to erosion pattern in circulating fluidized bed boiler B Sudarmanta JMES The International Journal of Mechanical Engineering and Sciences 1 (2 …, 2017 | 3 | 2017 |
Numerical study of epoxy-ramie fiber composite as a type iv ballistic resistant material S Sutikno, RF Rizal, A Safaat JMES The International Journal of Mechanical Engineering and Sciences 5 (1 …, 2021 | 2 | 2021 |
Design of a Patient Wrist Rehabilitation Device with Servo Motor Drive LY Amali, IML Batan JMES The International Journal of Mechanical Engineering and Sciences 4 (2 …, 2020 | 2 | 2020 |
Failure analysis of superheater tubes made from material T91 in the boiler of a 600 MW power plant KA Munif JMES The International Journal of Mechanical Engineering and Sciences 4 (1 …, 2020 | 2 | 2020 |
Experimental Study of the Effect of Magnetization on Bioethanol Injectors on Spray Characteristics for Applications in the SINJAI-150 Engine IBS Amalia Dwi Utami, Bambang Sudarmanta, Budi Utomo Kukuh Widodo, Ary ... JMES The International Journal of Mechanical Engineering and Sciences 3 (no …, 2019 | 2* | 2019 |
Failure Analysis of Bend Tube Preheater on Heat Recovery Steam Generator RSE Putro, A Hariyadi, S Suwarno JMES The International Journal of Mechanical Engineering and Sciences 1 (1 …, 2017 | 2 | 2017 |
Numerical study of heat transfer characteristics in high pressure steam turbine during stop unit process with sliding pressure B Santoso, BA Dwiyantoro JMES The International Journal of Mechanical Engineering and Sciences 6 (2 …, 2022 | 1 | 2022 |
Engine RPM and Battery SOC Activation Optimization in Hybrid Vehicle Energy Management System Utilizing BPNN-Genetic Algorithm and BPNN–Particle Swarm Optimization RAM Wicaksana, B Sudarmanta, MK Effendi JMES The International Journal of Mechanical Engineering and Sciences 6 (2 …, 2022 | 1 | 2022 |
Determination of Injection Molding Process Parameters using Combination of Backpropagation Neural Network and Genetic Algorithm Optimization Method A Wahjudi, TD Salamoni, IML Batan, D Harnany JMES The International Journal of Mechanical Engineering and Sciences 5 (2 …, 2021 | 1 | 2021 |
Enhancing Savonius Turbine Self-starting Capability by Installing a Circular Cylinder in Front of Returning Turbine Blade TY Yuwono, RA Bagas, P Suksmatatya, MM Festy, L Elza, NA Vega, ... JMES The International Journal of Mechanical Engineering and Sciences 5 (1 …, 2021 | 1 | 2021 |
Modified Archad’s Equation to Estimate Wear Volume due to Sliding Speed Y Kaelani, BA Permana JMES The International Journal of Mechanical Engineering and Sciences 5 (1 …, 2021 | 1 | 2021 |
Experimental And Numerical Study Of Two Dimensional Flow Of Bubble Separation Over The Leading Of Thickness Plate H Sasongko, AH Irfani JMES The International Journal of Mechanical Engineering and Sciences 4 (2 …, 2020 | 1 | 2020 |
Analysis of Power System and Drivetrain Component Design for Toyota Calya Electric Car PN Auliya, IN Sutantra JMES The International Journal of Mechanical Engineering and Sciences 4 (2 …, 2020 | 1 | 2020 |
Stress Analysis of Solar Electric Bus Chassis Using Finite Element Method A Wikarta, YA Yudha JMES The International Journal of Mechanical Engineering and Sciences 4 (1 …, 2020 | 1 | 2020 |