Tool wear effect on cutting forces: In routing process of Aleppo pine wood H Aknouche, A Outahyon, C Nouveau, R Marchal, A Zerizer, JC Butaud journal of materials processing technology 209 (6), 2918-2922, 2009 | 66 | 2009 |
Deposition and characterization of titanium aluminum nitride coatings prepared by RF magnetron sputtering AZ Ait-Djafer, N Saoula, H Aknouche, B Guedouar, N Madaoui Applied Surface Science 350, 6-9, 2015 | 58 | 2015 |
Applications of CrAlN ternary system in wood machining of medium density fibreboard (MDF) Y Benlatreche, C Nouveau, R Marchal, JPF Martins, H Aknouche Wear 267 (5-8), 1056-1061, 2009 | 38 | 2009 |
Comparison of CrAlN layers obtained with one (CrAl) or two targets (Cr and Al) by magnetron sputtering C Nouveau, B Tlili, H Aknouche, Y Benlatreche, B Patel Thin Solid Films 520 (7), 2932-2937, 2012 | 26 | 2012 |
Physical and mechanical properties of CrAlN and CrSiN ternary systems for wood machining applications Y Benlatreche, C Nouveau, H Aknouche, L Imhoff, N Martin, J Gavoille, ... Plasma Processes and Polymers 6 (S1), S113-S117, 2009 | 26 | 2009 |
An ecological water-based drilling mud (WBM) with low cost: substitution of polymers by wood wastes S Haider, MZ Messaoud-Boureghda, H Aknouche, A Akkouche, ... Journal of Petroleum Exploration and Production Technology 9 (1), 307-313, 2019 | 20 | 2019 |
Parametric study of the mechanical properties of nanocrystalline TiN/CrN multilayer coatings with a special focus on the effect of coating thickness and substrate roughness TD Atmani, M Gaceb, H Aknouche, C Nouveau, MS Bouamrene Surfaces and Interfaces 23, 101001, 2021 | 14 | 2021 |
Incorporation mode effect of Nano-silica on the rheological and mechanical properties of cementitious pastes and cement mortars B Safi, H Aknouche, H Mechakra, D Aboutaleb, K Bouali IOP Conference Series: Earth and Environmental Science 143 (1), 012015, 2018 | 12 | 2018 |
Effects of Nitrogen Content on the Structural, Mechanical, and Corrosion Properties of ZrN Thin Films Grown on AISI 316L by Radiofrequency Magnetron Sputtering M Azibi, N Saoula, N Madaoui, H Aknouche Crystal Research and Technology 56 (12), 2100096, 2021 | 9 | 2021 |
Etude de l’usure des outils de coupe traités dans le domaine de l’usinage du bois H Aknouche | 8 | 2009 |
The influence of substrate bias voltage on the electrochemical properties of ZrN thin films deposited by radio-frequency magnetron sputtering: Biomedical application M Azibi, N Saoula, H Aknouche Journal of Electrical Engineering 70 (7), 112-116, 2019 | 7 | 2019 |
A Study of Cr/CrN and Cr/CrN/CrAlN Multilayer Coatings for Permanent Mold Castings of Aluminum Alloys: Wear and Soldering Tendency MS Bouamerene, C Nouveau, H Aknouche, A Zerizer, TD Atmani, ... Journal of Materials and Engineering Structures 8 (1), 83-94, 2021 | 3 | 2021 |
Proceedings of the Third International Symposium on Materials and Sustainable Development B Abdelbaki, B Safi, M Saidi Springer, 2018 | 3 | 2018 |
A predictive model of the optimal tool edge geometry for veneer cutting processes FZ Bouarab, AH Aknouche, A Hamrani Machining Science and Technology 23 (5), 758-778, 2019 | 2 | 2019 |
Bias voltage effect on magnetron sputtered titanium aluminum nitride TiAlN thin films properties ZA Ait-Djafer, N Saoula, D Wamwangi, N Madaoui, H Aknouche The European Physical Journal Applied Physics 86 (3), 30301, 2019 | 2 | 2019 |
Characterization of algerians oak wood by x-Ray tomographic scanner and free software image-J K Salim, Z Abdelatif, S Nourdine, A Abdelhamid, A Boumerdès, F Mothe Wood research 59 (2), 335-342, 2014 | 2 | 2014 |
Mesure des efforts de défonçage et de la qualité finale en usinant en différents angles du fil: comparaison entre le pin Douglas et le pin d'Alep H Aknouche, G Goli, R Marchal, J Sandak, A Zerizer, JC Butaud BOIS & FORETS DES TROPIQUES 313, 85-93, 2012 | 2 | 2012 |
Improvement of the tribological behavior of TiN/CrN multilayer coatings by modulation wavelength variation TD Atmani, MS Bouamerene, M Gaceb, C Nouveau, H Aknouche Tribology International 192, 109226, 2024 | 1 | 2024 |
Optimization of tool geometry parameters for rotary peeling veneer process based on TLBO algorithm FZ BOUARAB, H Aknouche, A Hamrani S1-Procédés de fabrication et mise en forme par grandes déformations, 1-18, 2017 | 1 | 2017 |
Caractérisation des bois de chêne Algériens par Scanner tomographique à rayons X et logiciel libre Image-J. S Kennouche, F Mothe, A Zerizer, A Aknouche Journal of Materials, Processes and Environment December edition 1 (2), 142-146, 2013 | 1 | 2013 |