Modelling the interfacial damage of carbon fiber reinforced polymer composite laminate under the low-velocity impact loading MS Meon, JB Saedon, S Shawal, H Husain, MF Othman, MN Rao, ... IOP Conference Series: Materials Science and Engineering 1092 (1), 012043, 2021 | 439 | 2021 |
Improving tensile properties of kenaf fibers treated with sodium hydroxide MS Meon, MF Othman, H Husain, MF Remeli, MSM Syawal Procedia Engineering 41, 1587-1592, 2012 | 178 | 2012 |
Influence of fins designs, geometries and conditions on the performance of a plate-fin heat exchanger-experimental perspective MIN Ma’Arof, GT Chala, H Husain, MSS Mohamed Journal of Mechanical Engineering and Sciences 13 (1), 4368-4379, 2019 | 14 | 2019 |
Diversification of temporal sewage loading concentration in tropical climates ZM Hanafiah, WHMW Mohtar, HA Hasan, HS Jensen, MZ Abdullah, ... IOP Conference Series: Earth and Environmental Science 264, 012026, 2019 | 11 | 2019 |
Computational model analysis on a bipolar plate flow field design of a PEM fuel cell KI Sainan, R Atan, H Husain, W Mohamed 2011 5th International Power Engineering and Optimization Conference, 133-138, 2011 | 8 | 2011 |
Influence of cutting edge radius in micromachining AISI D2 JB Saedon, AHA Halim, H Husain, MS Meon, MF Othman Applied Mechanics and Materials 393, 253-258, 2013 | 7 | 2013 |
A study on kerf and material removal rate in wire electricaldischarge machining of Ti-6Al-4V: Multi-objectives optimization JB Saedon, N Jaafar, MA Yahaya, NHM Nor, H Husain 2014 2nd International Conference on Technology, Informatics, Management …, 2014 | 5 | 2014 |
Optimizing sintering process to produce highest density of porous Ti-6Al-4V NH Mohamad Nor, H Nor Hafiez, MA Yahaya Journal of Mechanical Engineering (JMechE), 44-55, 2018 | 4 | 2018 |
Muscular activities measurements of forward lean and upright sitting motorcycling postures via surface electromyography (sEMG) MIN Ma’arof, AR Omar, R Haron, H Husain, MA Wahab MATEC Web of Conferences 135, 00046, 2017 | 4 | 2017 |
Characterisation of recycled aluminium swarf into fine powder for MIM applications via ball milling SB Yussoff, NH Mohd Nor, H Husain Journal of Mechanical Engineering (JMechE), 164-175, 2019 | 3 | 2019 |
Potential utilization of biodiesel as alternative fuel for compression ignition engine in Malaysia MA Wahab, MIN Ma’arof, IN Ahmad, H Husain IOP Conference Series: Materials Science and Engineering 257 (1), 012074, 2017 | 3 | 2017 |
Multi-objective optimization in wire-electrical discharge machining (WEDM) of titanium alloy JB Saedon, N Jaafar, NHM Nor, MA Yahaya, H Husain Jurnal Teknologi 76 (6), 2015 | 3 | 2015 |
Influence of machining parameters on surface roughness in WEDM titanium alloy JB Saedon, PJR Ding JR, MSM Shawal, H Husain, MS Meon Advanced Materials Research 701, 349-353, 2013 | 3 | 2013 |
Investigation of the Amount of Energy Absorption of Aluminium Tube: Inversion and Concertina Collapse Mode MS Meon, H Husain Advanced science engineering information technology 2 (3), 69-73, 2012 | 3 | 2012 |
Sintered strength of Ti-6Al-4V by metal injection molding (MIM) using palm stearin binder NHM Nor, H Husain, MH Ismail, JB Saedon, M Newishy Journal of Mechanical Engineering (JMechE) 16 (1), 135-147, 2019 | 2 | 2019 |
Compressive mechanical properties of porous TI-6AL-4V with palm stearin binder system NHM Nor, JB Saedon, NAA Kasim, MH Ismail, H Husain Jurnal Teknologi 76 (6), 2015 | 2 | 2015 |
Modeling of alkali-silica reaction in a two phased material model Z Itam, H Husain UITM Jurnal Teknologi (Sciences & Engineering) 76 (9), 13-17, 2015 | 2 | 2015 |
Separation efficiency analysis of multiphase flow inside hydrocyclone using CFD MM Mahat, H Husain, NS Mohamad Journal of applied engineering design and simulation 3 (1), 51-65, 2023 | 1 | 2023 |
Influence of Cutting Parameter and Multi-Objective Optimization on Turning Titanium Alloy JB Saedon, MF Othman, MS Meon, NHM Nor, H Husain, S Shawal IOP Conference Series: Materials Science and Engineering 1092 (1), 012060, 2021 | 1 | 2021 |
Modelling Kerf Width in WEDM titanium alloy using response surface methodology JB Saedon, N Jaafar, MA Yahaya, NH Mohamad Nor, H Husain Key Engineering Materials 737, 83-89, 2017 | 1 | 2017 |