| MgH2-SiC based hydrogen storage material prepared by reactive mechanical alloying method Z Jalil, A Rahwanto, H Akhyar, R Razali, E Handoko IOP Conference Series: Earth and Environmental Science 105 (1), 012098, 2018 | 32 | 2018 |
| Hot tearing susceptibility of aluminum alloys using CRCM-Horizontal mold H Akhyar, V Malau, PT Iswanto Results in physics 7, 1030-1039, 2017 | 30 | 2017 |
| Desorption properties of mechanically milled MgH2 with double catalysts Ni and SiC A Rahwanto, Z Jalil, Akhyar, E Handoko IOP Conference Series: Materials Science and Engineering 931 (1), 012012, 2020 | 26 | 2020 |
| Magnetic behavior of natural magnetite (Fe3O4) extracted from beach sand obtained by mechanical alloying method Z Jalil, A Rahwanto, Mustanir, H Akhyar, E Handoko AIP Conference Proceedings 1862 (1), 030023, 2017 | 26 | 2017 |
| Study on Cooling Curve Behavior During Solidification and Investigation of Impact Strength and Hardness of Recycled Al–Zn Aluminum Alloy H Akhyar, Husaini International Journal of Metalcasting 10 (4), 452-456, 2016 | 26 | 2016 |
| Structural Simulations of Bicycle Frame Behaviour under Various Load Conditions Akhyar, Husaini, H Iskandar, F Ahmad Materials Science Forum 961, 137-147, 2019 | 21 | 2019 |
| Hydrogen storage properties of mechanical milled MgH2-nano Ni for solid hydrogen storage material Z Jalil, A Rahwanto, E Handoko, H Akhyar IOP Conference Series: Materials Science and Engineering 432 (1), 012034, 2018 | 20 | 2018 |
| Non Treatment, T4 and T6 on Tensile Strength of Al-5.9Cu-1.9Mg Alloy Investigated by Variation of Casting Temperature A Hasan, PT Iswanto, V Malau Materials Science Forum 929, 56-62, 2018 | 20 | 2018 |
| Effect of shot peening at different almen intensities on fatigue behavior of AISI 304 PT Iswanto, H Akhyar, FF Utomo Metalurgija 57 (4), 295-298, 2018 | 16 | 2018 |
| MODIFICATION OF CONSTRAINED ROD CASTING MOLD FOR NEW HOT TEARING MEASUREMENT V Malau, Akhyar, PT Iswanto Archives of Metallurgy and Materials 63 (3), 1201-1208, 2018 | 16 | 2018 |
| Effect of shot peening on microstructure, hardness, and corrosion resistance of AISI 316L PT Iswanto, H Akhyar, A Faqihudin Journal of Achievements in materials and manufacturing Engineering 89 (1), 2018 | 16 | 2018 |
| Perancangan dan Pembuatan Dapur Peleburan Logam dengan Menggunakan Bahan Bakar Gas (LPG) AZ Mubarak, H Akhyar Jurnal Teknik Mesin Unsyiah 1 (3), 128-132, 2013 | 14 | 2013 |
| Experiment on Hardness and Impact Strength of Recycled Aluminum Alloys by Metal Casting Process F Ahmad, Akhyar, A Masri Materials Science Forum 961, 65-72, 2019 | 13 | 2019 |
| Effect of Different Gating Systems and Sand Mold Binder on the Cast-Quality of Bicycle Frame Produced through Sand Casting Method Akhyar, Husaini, M Ali, N Ali, F Ahmad Defect and Diffusion Forum 402, 100-107, 2020 | 12 | 2020 |
| Fatigue crack growth rate of motorcycle wheel fabricated by centrifugal casting PT Iswanto, Akhyar, EUK Maliwemu Metalurgija 58 (1-2), 51-54, 2019 | 12 | 2019 |
| Influence of shot peening on surface properties and corrosion resistance of implant material AISI 316L PT Iswanto, RI Yaqin, Akhyar, HM Sadida Metalurgija 59 (3), 309-312, 2020 | 10 | 2020 |
| Heat treatment T4 and T6 effects on mechanical properties in Al-Cu alloy after remelt with different pouring temperatures PT Iswanto, Akhyar, Pambekti Metalurgija 59 (2), 171-174, 2020 | 9 | 2020 |
| Experimental investigation on open sun-drying and solar drying system of bilimbi D Harun, MI Maulana, H Akhyar 2016 6th International Annual Engineering Seminar (InAES), 271-275, 2016 | 8 | 2016 |
| Stress and strain analysis from dynamic loads of mechanical hand using finite element method I Hasanuddin, Husaini, MS Anwar, SY B.Z., H Akhyar The 7th AIC‐ICMR on Sciences and Engineering 2017 352, 1-5, 2018 | 7 | 2018 |
| Effect of T6 heat treatment and artificial aging on mechanics and fatigue properties of A356. 0 aluminum alloy produced by 350 rpm centrifugal casting PT Iswanto, H Akhyar, V Malau, R Wirawan 2016 6th International Annual Engineering Seminar (InAES), 223-227, 2016 | 7 | 2016 |
